FrostyTech.com Heatsink Reviews and Analysis
   
  

TOP 5 Heat Sinks     TOP 5 Low Profile Heat Sinks     TOP 5 Liquid Coolers    
 Heatsinks by Brand / Mfgr      Reviews + Articless     Advanced Search    

Thermaltake ISGC-400 Heatsink Review
Thermaltake ISGC-400 Heatsink Review
  77%   
Abstract: Thermaltake's ISGC-400 is a lower noise low profile heatsink suitable for media PC or other compact chassis. The Thermaltake ISGC-400 heatsink comes with fan that has beautiful glossy white fan blades shaped like the fins of a whale.

 Manufacturer  Category  Published  Author 
Thermaltake   Cooling / Heatsinks   Nov 22, 2009   Max Page  

Thermaltake's ISGC-400 is a lower noise low profile heatsink suitable for media PC or other compact chassis. The aluminum cooling fins on the ISGC-400 are widely spaced to allow air from the single 120mm fan to pass through easily, so a high speed fan isn't needed. Six 6mm diameter copper heatpipes ensure good thermal conduction from the base to the saw-toothed fins and a small manual fan speed controller attached to the fan power cable allows fan speed to be adjusted from 800-1300RPM for situations which demand the least noise possible.

The Thermaltake ISGC-400 heatsink comes with fan that has beautiful glossy white fan blades shaped like the fins of a whale. The fan motor used Hydro Dynamic Bearings to decrease noise and improve lifespan (MTBF 50,000 hours), always a nice touch.

The 615gram ISGC-400 will fit in low profile computer systems where tower heatsinks cannot tread, at 102mm in height this includes 3U-sized PC cases. The heatsink installs onto Intel socket 775/1366 and AMD socket AM2/AM3 processors and should run about $34 USD/CDN.

Thermaltake ISGC-400 Heatsink
heatsink specsheet
manufacturer: thermaltake
model no.: isgc-4000
materials: aluminum fins, copper heatpipes, aluminum base with copper baseplate
fan mfg: thermaltake ttb122512ls
fan spec: 800-1300rpm, 12v, 0.33a
fan airflow: 58cfm
fan dim: 25x120x120mm
heatsink & fan dim: 102x126x151mm
weight: 615 grams
includes: multi-socket socket mounting hardware, thermal compound, instructions

Compatible with Sockets:
AMD - AM2/AM2+/AM3
Intel - LGA775/1366
Pricing: $34USD ($34CDN)

Mounting brackets for the Thermaltake ISGC-400 screw into a large extruded aluminum heatsink soldered to the opposite side of the line of heatpipes at the base. The bottom of the heatsink that makes contact with the processor is actually a 2mm thin copper plate, rather than the more complicated exposed heatpipe type. If the heatpipes are doing their job properly, this heatsink at the bottom of the ISGC-400 shouldn't ever get very hot. I suppose owing to the top-down airflow it does add additional useful cooling surface area however.

Mounting Hardware and Brackets

Thermaltake's ISGC-400 heatsink heatsink is compatible with Intel socket 775/1366 and AMD socket AM2/AM2+/AM3 processors. Heatsink installation requires access to the rear of the motherboard to install small nuts, as the overhang of the large 120mm aluminum cooling fin array makes tool access difficult. Intel LGA1156 processors are not supported. The ISGC-400 heatsink accomodates one 120mm fan, held in place with wire fan mounting clips.

The installation hardware isn't the easiest to use, but does hold the heatsink firmly in place once installed. Getting at the CPU afterward is likely to be a bit of a pain though.

Base Finish and Flatness

Flipping a heatsink over to inspect the business end is often a simple indicator of overall cooler quality. More practically speaking, a heatsink is in many ways only as effective as the contact it makes with the processor - the flatter and smoother the better. Base finish is one of the criteria that Frostytech measure in the course of evaluating heatsinks, and it involves two distinct aspects. Surface Finish is the first; this is calculated with the aid of Surface Roughness Comparator that has a cross section of common machine surface finishes and their numerical surface roughness equivalents in microinches. The second is Surface Flatness. This is tested with an engineers straight edge or proven flat surface, in two axis.

The stamped copper base plate has a polished finish, surface roughness is approximately 8 microinches, which is considered good. The base is perfectly flat in both axis.

FrostyTech's Test Methodologies are outlined in detail here if you care to know what equipment is used, and the parameters under which the tests are conducted. Now let's move forward and take a closer look at this heatsink, its acoustic characteristics, and of course its performance in the thermal tests!

° Next Page 

Table of Contents:

 1: — Thermaltake ISGC-400 Heatsink Review
 2:  360° View - Thermaltake ISGC-400 Heatsink
 3:  Heatsink Sound Measurement
 4:  AMD Heatsink Temperature Comparisons
 5:  Intel LGA775 Heatsink Temperature Comparisons

List all Thermaltake heat sinks that Frostytech tested?

Facebook RSS Feed Twitter
Resources
° Got Feedback?
° Mk.II Test Platform
° Where To Buy?
° Manufacturer Index
° Industry Dir.
° Cooling Projects
Recently Tested

Scythe Mugen 5 Rev B SCMG-5100 Heatsink Review

Gelid Tranquillo 4 Air Cooled Heatsink Review

Coolermaster Ergostand III Laptop Cooling Stand Review

Noctua NH-D9DXi4-3U LGA2011 Xeon Server/Workstation Heatsink Review

Noctua NH-L9x65 Low Profile Heatsink Review

Scythe Fuma SCFM-1000 Heatsink
...More Articles >>


Websites you may also like:
PCSTATS


FrostyTech.com
Since June 1999


Find a Heatsink
Latest Heatsink Reviews
Top 5 Heatsinks Tested
Top 5 Low Profile Heatsinks
Top 5 Liquid Coolers
Heatsinks by Mfgr / Brand


Social Media
Facebook
Twitter
Pinterest


FrostyTech.com Info
Feedback
Contact Us / Heatsink Submissions
Submit News
Privacy Policy
Suite 66

© Copyright 1999-2023 www.frostytech.com All Rights Reserved. Privacy policy and Terms of Use
Images © FrostyTech.com and may not be reproduced without express written permission. Current students and faculty of accredited Universities may use Frostytech images in research papers and thesis, provided each image is attributed.